Existing Boiler Job Ready Package

50’ From Furnace to Home

Plus 50’ Inside Home

Factory Pre-Plumbing Saves You 4 to 6 Hours

• 1 - 6' x 6' Geotextile Ground Cover
• 4 -12x12x1 Foot Pads
• 1 - Standard Back of Furnace w/011 pump
• 1 - TACO 011 Circulator Pump (for up to 50')
  • 1 - 1" Threaded flanges for circulator (set)
  • 2 - 1" Brass Full Port Ball Valves (threaded)
  • 2 - 1" PEX x 1" Male Adapter fittings
  • 2 - 1" PEX Crimp Rings
  • 1 - 1" Brass x 2" Nipple
  • 2 - 1" Brass 45 Ell
  • 1 - 1" Brass Cap
  • 1 - 1" Brass Plug
  • 1 - 1" Brass 90 Ell
  • 4 - 1" Brass x Close Nipple
  • 1 - 3/4" Bronze Boiler Drain
  • 1 - 3/4" x 3/4" Hose Swivel Adapter
  • 2 - Rubber Washer

Between The Home and The Furnace (Underground)

(Enough material to set the furnace 50' from the home. Additional distance is available.)

• 100' - 1" High temperature flexible PEX pipe (cross-linked polyethylene)
• 7 - 8' MAXX-R polyethylene closed-cell foam insulation pieces (56' distance)
• 6 - MAXX-R Joint Connector Boots
• 2 - MAXX-R Protective End Cap Boot
• 12 - Joint Boot Ties
• 6' - 1 1/8" ID x 1" wall Transition Insulation

Inside The Home

• 50' - 1" High temperature flexible PEX pipe (cross-linked polyethylene)
• 54' - 1-1/8" ID x 1/2" wall closed-cell insulation (to cover the pipes inside/under the home)
• 1 - Roll of 2" wide closed cell insulation tape (to join the insulation)
• 10 - 1" PEX x 1" PEX Brass elbows
• 2 - 1" PEX couplings
• 24 - 1" PEX Crimp Rings

1 - Inline Air Removal Drain Kit

This little package allows you to use your home's water supply to purge the hydronic system of air.

• 1 - 3/4" x 3/4" Hose Swivel Adapter
• 2 - Rubber Washer
• 1 - 3/4" Bronze Boiler Drain
• 1 - 1" x 1" x 3/4" Threaded Brass Tee
• 2 - 1" PEX x 1" Male Adapter fittings
• 2 -1" PEX Crimp Rings
• 1 - Labor to assemble and test

Existing Boiler

(Illustration)

Water-To-Water Heat Plate Exchanger

• 1 - 225,000 BTU - 44 Plate Stainless Steel Water-To-Water Heat Exchanger
• 1 - Stainless Steel Flat Plate Heat Exchanger Assembly self install kit including:
  • 2 - 1" WROT FRG x M Adapter
  • 2 - 1" WROT FRG x STR LT 90 EII
  • 2 - 1" WROT CxC Union
  • 2 - 1" WROT FTG x FIP Adapter
  • 2 - 1" Brz 400# Thrd Ball Valve
  • 2 - 1" PEX Barb x 1" MPT Adapter
  • 2 - 1" PEX Crimp Ring
• 1 - Industry Leading Installation Manual

Maintain Your CrossFire™

Included FREE with purchase of package

Protect your investment and maintain your warranty by correctly treating the water in your furnace.

Wood Burning Furnace Water Treatment Kit includes:

• 1 gallon of Certified Laboratories “Outdoor Furnace Water Treatment” chemical (treats up to 300 gallons).
• 4 sample bottles for treated furnace water.
• 4 shipping containers, labels and instructions for treated water sample bottles.
• 4 furnace water analyses and reports produced by Certified Laboratories.
• Instructions and procedure sheet.